- Features vertical sheet metal roof panels and horizontal side panels
- Customize with pedestrian doors, garage doors and gables
- Engineered to meet local snow and wind load requirements in most areas
- Available in packaged kits, or frame only, and can be sheeted with a standard sheet metal package or add your own vinyl, wood, brick, stucco, or other roofing/siding alternative
Watch An Assembly Video
Frontier Garage applications include:
- Car / Truck / Boat garage
- Equipment storage
- Retail space
- Home office
- Recreational building
- Hunting cabin
The Frontier Garage Series features vertical sheet metal roofing panels and horizontal siding panels, requiring roof purlins but no side girts.
No side girts mean fewer frame components, so the Frontier design offers a lower cost alternative to the Summit building style.
Engineering certified to 30’ wide and up to 12’ sidewall height, assembly time is drastically reduced with VersaTube’s patented Slip-Fit frame connections.
Frontier Garage Standard Sizes
Personalize your buildings with these accessories:
Available Colors (Roofing & Siding)
While colors have been matched as accurately as possible to the actual finish, representation of colors may vary due to monitor and printing limitations. Availability of colors are subject to change.
- Premium 29 gauge painted steel roofing and siding panels deliver a quality professional look
- Low maintenance, easy-to-clean finish resists chalking, fading, stains and dirt retention
- 80,000 PSI minimum yield strength
- 20-year limited paint warranty
- Color-matched trim and accessories included
VersaTube garages can be quoted with shipping to the following states. ALABAMA, AL, ARIZONA, AZ, ARKANSAS, AR, CALIFORNIA, CA, COLORADO, CO, CONNECTICUT, CT, DELAWARE, DE, FLORIDA, FL, GEORGIA, GA, IDAHO, ID, ILLINOIS, IL, INDIANA, IN, IOWA, IA, KANSAS, KS, KENTUCKY, KY, LOUISIANA, LA, MAINE, ME, MARYLAND, MD, MASSACHUSETTS, MA, MICHIGAN, MI, MINNESOTA, MN, MISSISSIPPI, MS, MISSOURI, MO, MONTANA, MT, NEBRASKA, NE, NEVADA, NV, NEW HAMPSHIRE, NH, NEW JERSEY, NJ, NEW MEXICO, NM, NEW YORK, NY, NORTH CAROLINA, NC, NORTH DAKOTA, ND, OHIO, OH, OKLAHOMA, OK, OREGON, OR, PENNSYLVANIA, PA, RHODE ISLAND, RI, SOUTH CAROLINA, SC, SOUTH DAKOTA, SD, TENNESSEE, TN, TEXAS, TX, UTAH, UT, VERMONT, VT, VIRGINIA, VA, WASHINGTON, WA, WEST VIRGINIA, WV, WISCONSIN, WI, WYOMING, WY,
VersaTube is proud to offer steel tubing made in the U.S.A. with gauges that range from 15 to 12 gauge depending size and configuration. Should you have an unusual load requirement, your dealer will be able to properly configure the design of your garage to meet these needs.
Yes. Our VersaTube Building System allows for any size garage or RV garage to be built up to 52′ wide, 16′ sidewall and unlimited length.
VersaTube offers sheet metal in nine standard colors and we will gladly search for colors outside our color chart.
Want to save some money? VersaTube offers premier do-it-yourself garage kits. Most VersaTube dealers offer kits and they are also available at most Home Centers such as Lowe’s, Home Depot, Menards, and Sutherlands. We have a detailed step-by-step assembly manual to help you every step of the way. Our Slip Fit connections allow us to produce a garage kit that is easy to get home and easier to assemble. Your dealer is readily available to assist you. You may call our hot line for assistance at 800-900-7222.
VersaTube follows state and federal laws on sales tax. We do not charge taxes to the federal government, state government or any organization on products for resale with a valid Tax Exemption Number.
VersaTube uses a proprietary method when mandrel-bending side posts. VersaTube mandrel bends maintain the integrity and strength of the steel garage framing. Some models offered utilize single point compression bending.
VersaTube utilizes shaped tubing for 2 reasons. One, garages built with square or rectangular tubing are significantly stronger that those using round tubing. The flat surface on shaped tubing provides for easier assembly when applying screws and sheet metal panels.
VersaTube prefabricated garage kits are conveniently packaged and shipped on 40″ x 120″ pallets. Even the largest steel canopies can be delivered by any major shipping company using a standard pallet jack and lift gate.
Garages can be built on a number of flat surfaces following the anchoring procedures provided in the installation manual.
16. Can VersaTube garages be built and then completely enclosed with additional materials at a later date?
The VersaTube Building System is designed for this exact purpose. Additional sections can be added and your garage can even be enclosed at a later date without issue.
Most prefab garage kits we sell are 14′ x 38′ x 12′ and easily fit a motor home with an air conditioner underneath.
Yes, but attaching to an existing structure will require additional engineering.
Yes, our customer service hot line fields calls Mon-Fri from 8AM to 5PM
Authorized VersaTube dealers can install our garages as boat slips covers at their discretion.
The garage industry generally refers to an 18-foot garage as a doublewide. VersaTube offers doublewide units in both an 18′ and 20′ wide configuration. Additionally, our Suburban Series garage line is a full foot wider than the industry standard singlewide (12′ wide) and doublewide (18′ wide) garages. For two large vehicles, we recommend a 24′ x 24′ garage. For two small vehicles, a 20′ x 20′ garage may do the job.
You will find a link to our garage assembly manual in the top section of this page.
Generally our standard steel garage does not require truss braces in widths narrower then 20′ wide unless you have higher snow and wind load requirements. Most steel garages 20′ wide, and wider require truss braces to meet local wind and snow load requirements.
VersaTube offer garages in a 3:12 roof pitch.
Snow and wind load conditions dictate the required on center spacing of a garage: VersaTube 12′ to 20′ wide garages are 5′ on center. VersaTube 24′ to 30′ wide garages are 4′ or 5″ on center VersaTube Contractors Series 2″x4″ framing allows for garages wider than 30′.
Yes. Our garages and RV garages come in many different styles. The Summit Series garage and the Frontier Series garage have the A-Frame style look.
Standard metal garages range from 8′ wide to 30′ wide and take 4 – 12 hours to assemble. Adding sidewalls, a front or back to your garage adds to the assembly time.
Here is the formula to calculate peak height (((Width / 2) x 3) / 12) + sidewall height
It is important to leave enough room to work around the perimeter of the metal garage for assembly purposes. We also recommend checking your local building codes.
VersaTube garages use common 7″ concrete anchor bolts that are installed using a hammer drill.
Our metal garages can be financed through credit accounts with mass merchants. Some of our dealers also offer financing. See our Dealer Locater to find a dealer near you.
Our garages can be purchase with cash, Visa, MasterCard, American Express, Discover, money order, debit card, personal check, and business check or by PO (purchase order) to pre-qualified customers.
See our Dealer Locater and in cases where a garage dealer is not located in your proximity, give us a call 800-900-7222.
Framing for one single gable end garage door opening is included in the standard garage package. Other gable end modifications are available if requested and approved in advance by VersaTube. Eave side door openings in 8’ and 10’ heights and widths up to 10’ are also available. Reference the listing in the appropriate product section of this binder or in the separate pricing booklet.
No garage doors are included in the standard garage package, but may be added to the order. Reference the required model number in the appropriate section of this binder or in the separate pricing booklet.
One kit is included in the standard garage package. Additional 3’0” wide x 6’8” high side entry door frame kit for eave side installation. For a 12’ or 20’ wide garage, order one VH-D5 for each additional side door frame your customer is requesting. For a 24’ or 30’ wide garage, the side door frame model number changes to VH-D4. Reference the listing in the appropriate product section of this binder or in the separate pricing booklet.
No pedestrian doors are included in the standard garage package, but may be added to the order. Reference the series number and style in the appropriate section of this binder or in the separate pricing booklet.
No window frames are included in the standard garage package, but may be added to the order. 2’-3’ wide x 3’-5’ high window frame kit for eave side installation. For 12’ or 20’ wide garage, order one VH-W5 for each window frame desired. For 24’ or 30’ wide garage, the window frame model number changes to VH-W4. Reference the listing in the appropriate product section of this binder or in the separate pricing booklet.
No windows are included in the standard garage package, but may be added to the order. Reference the series number, style and size in the appropriate section of this binder or in the separate pricing booklet.
Indicate choice of insulation – Reflective Radiant Barrier or VRR (with desired thickness). Reference the listing in the appropriate product section of this binder or in the separate pricing booklet.
or call us (800) 810-2993